ATV & Off Road Flags | Bicycle Flags | Large Flags
Clearance Sale

Fiberglass whip poles

1/4 inch black fiberglass whips
for smaller or light weight atv flags and bicycle safety flag poles.

5/16 inch fiberglass whips
for heavier ATV flags, aggressive riders or higher speed vehicles.
Available in black only.

3/8" fiberglass whips
a good choice for higher speed vehicles, sand rails or ATV's flying the larger,
heavier flags such as 2x3 or 3x5 flags.

7 - 8 foot one piece black fiberglass whips
***UPS Ground shipping only***

This item includes a one time oversized shipping fee of $4.00.
This fee is charged only once per item
and is not multiplied by quantity.

Whip Mounting Hardware
quick mounts, mount bolts and brackets

GLK Aluminum Quick Release

Solid 1 piece aluminum base, low profile
with lock washer, nut & thumb screw.

Available in the extremely hard to find 3/8 size!

GLK Tool and Machine has made these affordable,
high quality quick mounts by special request.
$22.50 ea.

Standard 1/2" Mount Bolt

Removable Split Bolt Mount
Includes 1/2 inch split bolt 1 inch long, locking nut, washer, lock washer and lock nut.
Fits fiberglass poles 1/4 and 5/16 inch sizes.
$3.95ea

Bicycle Safety Flag Bracket

* Works with any 1/4" - 7/16" bolt
* Colors: Galvanized silver
* Simple and Easy to install.
* Holds 1/4" diameter flag poles only.
* Mounts to any bicycle rear axle, or any bolt 7/16 of an inch or smaller.
* Flag wedges firmly into bracket.
Installation: Loosen the rear axle nut on the side of your bicycle.
Slide the bracket into place. Adjust the bracket to your desired angle,
and tighten the axle nut firmly.
This will work the same on any bolt that is 1/4 - 7/16 of an inch.

WheelerWhip Springy Thingy
1/4 & 5/16 quick mount

* Size 3 3/4" length x 1 1/4" diameter
* 1/4" & 5/16" whip sizes
* Simple and Easy to install.
* This Spring Mount is perfect for those
who are tired of breaking whips.
* Fits standard mounting tab.

Grommet Flag Mounting Kit

To mount flags with metal grommets to fiberglass flag poles
Kit includes two flag clips, 6 rubber o rings and a new end cap, instructions included.
Simply slide o rings on to whip on either side of clip, space to match flag's metal grommets.
A small dot of waterproof glue or an extra o ring can be used if sliding occurs.
Kits to fit 1/4", 5/16" and 3/8" whips.

Metal Flag Clamps

To mount flags with metal grommets to fiberglass flag poles
Package includes three flag clamps, bolt, lock nut and two sizes of washers to accommodate various sizes of brass grommets.
The three clamps allow mounting of one AditudeGear 2x3 OffRoad flag or stack two flags.
Kits to fit 5/16" and 3/8", 1/2", 3/4" size whips.

Sorry we are currently out of the 3/4 size but will have more in stock soon.

Nylon Flag Clamps

To mount flags with metal grommets to fiberglass flag poles
Package includes three flag clamps, bolt, lock nut and two sizes of washers to accommodate various sizes of brass grommets.
The three clamps allow mounting of one AditudeGear 2x3 OffRoad flag or stack two flags.
Kits to fit 3/8", 1/2", 3/4" size whips.

Sorry we are currently out of the 3/8 and 3/4 sizes but will have more in stock soon.

Aluminum Pole connecting ferrule

Fix broken whips or connect to make longer whips.
Package of 2 for 1/4" 5/16" and 3/8" whips.

Vinyl End caps
Package of 5 for 1/4" 5/16" and 3/8" whips.

Rubber pole grommets AKA flag stoppers or O rings

To mount casing style flags to 1/4, 5/16 or 3/8 fiberglass poles.

Package of 10 rubber grommets for mounting sleeved or casing style flags to your whip.
A small dot of waterproof glue or an extra grommet can be placed if sliding occurs.
For 1/4" 5/16" and 3/8" whips.

Flag Ties

To mount grommet style flags to flag poles.

Package of 10 heavy duty 120lb black flag ties.
1/4 inch wide X 6 inches long.

Mobility safety flag

Replacement flags

Available in yellow and orange
mouse over image for additional colors

Use as a Firestik replacement flag

High Visibility Pennant Flag

Measures approximately 10 x 15 inches, scrunch, stack or fly fully furled.
Very bright high visibility safety flag made from 100% polyester poplin.
Very strong, light weight and flexible fabric sewn heavy duty nylon thread, double stitched edges.
Replacement flag casing to fits up to a 3/8 inch pole including the Firestik brand poles.
Comes with rubber o rings to aid in mounting your flag.
Flag is suitable for all vehicles from bicycle flags to atv flags and will also hold up well for on and off road vehicle use.
Made in the USA

use as a Firestik replacement flag

High Visibility multi-purpose 12 x 18 Flag
Made from medium weight and very flexible 100% polyester,
sewn with heavy duty nylon thread and topped with a heavy duty poly pro webbing header
this flag is recommended for any vehicle type or for stationary safety flags.
Light weight enough to fly nicely n a light breeze but tough enough to hold up to higher speeds.
Available in High Visibility Orange and High Visibility Yellow.

Extremely tough vinyl coated mesh flag stands up to high speeds and extreme weather conditions.
The flow through design of the mesh drastically reduces wind drag and flag whip
making it a good choice not only for ATV flags but also for highway and off road vehicles to bicycles, golf carts, kyak,
snowmobile or use as marker safety flags.

Flag measures approximately 8x14, casing fits up to 3/8 whips
and replacement flag comes with rubber o ring flag stoppers to aid in mounting your flag,
please choose your pole size below.

Pics of this flag tested on our Jeep can be found on the gallery page.
Made in the USA

AditudeGear Mesh Grommet replacement safety flags

Extremely tough vinyl coated mesh flag stands up to high speeds and extreme weather conditions.
The flow through design of the mesh drastically reduces wind drag and flag whip
making it a good choice not only for ATV flags but also for highway and off road vehicles to bicycles, golf carts, kyak,
snowmobile or use as marker safety flags.

Flag measures approximately 9x15 with a heavy black header and brass grommets.
Perfect for use on lighted led whips, boats, sand rails, dune buggies, 4x4's or
specialty applications where a casing flag will not fit.
Made in the USA

$5.95ea

Qty:

**red and yellow are not high visibility colors**
flag color:
Choose flag style/color here orange pennant red pennant yellow pennant orange rectangle red rectangleyellow

---

AditudeGear Mesh extra large casing replacement safety flags

Extremely tough vinyl coated fire orange mesh flag stands up to high speeds and extreme weather conditions.
The flow through design of the mesh drastically reduces wind drag and flag whip
making it a good choice not only for ATV flags but also for highway and off road vehicles
to sand rails, UTV's, side by sides,dune buggies,
snowmobile or use as marker safety flags.

Flag measures approximately 9x14, casing fits up to a 1 inch pole.
Use as a replacement flag for larger lighted led whips, boats, 4x4's or
other specialty applications where a larger pole is used.
Made in the USA

$5.95ea

Qty:

---

These items are sold without warranty, expressed or implied
except for quality of construction.
No warranty or representation is made as to any product's ability to protect the user from accident or injury.
The user/purchaser assumes that risk.